Danh mục sản phẩm

Hỗ trợ trực tuyến

Lê Thanh Tùng
098 999 6869
Đỗ Khắc Tuấn
0988 789 656
Mai Phương Linh
0168 550 3413
Mai Mai
0982483504

Bản đồ

Thống kê truy cập

Linh kiện máy in

Bảng tra mã lỗi Toshiba 855 Full

Kick link bên dưới để tải ề máy cuả bạn 
 http://mayvanphonghaanh.com/admin/webroot/uploads/files/855_1.pdf
Code Description
Paper exit jam
 
 
E010
Paper not reaching fuser transport sensor: Paper which has passed the fuser unit does not reach the fuser transport sensor.
 
 
 
E020
Paper stopping at fuser transport sensor: The trailing edge of paper does not pass the fuser transport sensor after its leading edge has reached the fuser transport sensor.
Other paper jam
 
 
E030
Power-ON jam: Paper is remaining on the paper transport path of the equipment when the power is turned ON.
 
 
E061
Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment.
 
 
E062
Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.
 
 
E063
Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
 
 
E064
Incorrect paper size setting for 4th drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
 
 
E065
Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
 
 
E090
 
 
Image data delay jam: Image data to be printed cannot be prepared.
 
 
 
E091
Other time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
 
 
E0A0
Image transport ready time-out jam: Image data to be printed cannot be sent.
Paper misfeeding
 
 
 
 
 
E110
 
 
Transport jam during duplex printing (paper not reaching registration sensor): Paper which passed the reverse transport section does not reach the registration sensor during duplex printing.
 
 
 
E120
 
 
Bypass misfeeding (paper not reaching registration sensor): Paper fed out of the bypass tray does not reach the registration sensor.
 
 
 
E130
1st drawer misfeeding (paper not reaching 1st drawer feed sensor): Paper does not reach the 1st drawer feed sensor during the feeding at the 1st drawer.
 
 
 
E140
2nd drawer misfeeding (paper not reaching 2nd drawer feed sensor): Paper does not reach the 2nd drawer feed sensor during the feeding at the 2nd drawer.
 
 
 
 
 
 
E150
3rd drawer misfeeding (paper not reaching 3rd drawer / Tandem LCF feed sensor): Paper does not reach the 3rd drawer / Tandem LCF feed sensor during the feeding at the 3rd drawer.
 
 
 
E160
4th drawer misfeeding (paper not reaching 4th drawer feed sensor): Paper does not reach the 4th drawer feed sensor during the feeding at the 4th drawer.
 
 
 
E180
Option LCF misfeeding (paper not reaching Option LCF feed sensor): Paper does not reach the Option LCF feed sensor during the feeding at the Option LCF.
 
 
 
 
 
E190
 
 
Tandem LCF misfeeding (paper not reaching 3rd drawer / Tandem LCF feed sensor): Paper does not reach the 3rd drawer Tandem LCF feed sensor during the feeding at the Tandem LCF.
Paper transport jam
 
 
 
 
 
E200
 
 
1st drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 1st drawer.
 
 
 
 
 
E201
 
1st drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 1st drawer.
 
 
 
 
 
E210
 
 
2nd drawer transport jam (paper not reaching registration sensor):
Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 2nd drawer.
 
 
 
 
 
E211
 
2nd drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the
2nd drawer.
 
 
 
 
 
E220
 
2nd drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the 2nd drawer.
 
 
 
 
 
E230
 
1st drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 1st drawer feed sensor does not reach the 1st drawer transport sensor during the feeding at the 1st drawer.
 
 
 
 
 
E240
 
2nd drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 2nd drawer feed sensor does not reach the 2nd drawer transport sensor during the feeding at the 2nd drawer.
 
 
 
 
 
 
E250
Option LCF transport jam (paper not reaching Option LCF transport sensor): Paper does not reach the Option LCF transport sensor during the feeding at the Option LCF.
 
 
 
 
 
E260
 
 
Option LCF transport jam (paper not reaching registration sensor):
Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the Option LCF.
 
 
 
 
 
E261
 
Option LCF transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the Option LCF.
 
 
 
 
 
E2A1
 
Transport jam during duplex printing (paper not reaching intermediate transport sensor): Paper which has passed the reverse section and horizontal transport section does not reach the intermediate transport sensor during duplex printing
 
 
 
 
 
E300
 
 
3rd drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 3rd drawer.
 
 
 
 
 
E301
 
3rd drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 3rd drawer.
 
 
 
 
 
E310
 
3rd drawer transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd transport sensor does not reach the 1st drawer transport sensor during the feeding at the 3rd drawer.
 
 
 
 
 
E320
 
3rd drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 3rd drawer.
 
 
 
 
 
E330
 
 
4th drawer transport jam (paper not reaching registration sensor): Paper which has passed the 1st drawer transport sensor does not reach the registration sensor during the feeding at the 4th drawer.
 
 
 
 
 
E331
 
4th drawer transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st drawer transport sensor does not reach the intermediate transport sensor during the feeding at the 4th drawer.
 
 
 
 
 
 
 
 
E340
 
4th drawer transport jam (paper not reaching 1st transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the 4th drawer.
 
 
 
 
 
E350
 
4th drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 4th drawer.
 
 
 
 
 
 
E360
 
 
4th drawer transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 4th drawer transport sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the 4th drawer.
 
 
 
 
 
 
E370
 
 
3rd drawer transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 3rd drawer / Tandem LCF feed sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the 3rd drawer.
 
 
 
 
 
E380
 
 
4th drawer transport jam (paper not reaching 4th drawer transport sensor): Paper which passed the 4th drawer feed sensor does not reach the 4th drawer transport sensor during the feeding at the 4th drawer.
 
 
 
 
 
E3C0
 
 
Tandem LCF transport jam (paper not reaching registration sensor): Paper which has passed the 1st transport sensor does not reach the registration sensor during the feeding at the Tandem LCF.
 
 
 
 
 
E3C1
 
Tandem LCF transport jam (paper not reaching intermediate transport sensor): Paper which has passed the 1st transport sensor does not reach the intermediate transport sensor during the feeding at the Tandem LCF.
 
 
 
 
 
E3D0
 
Tandem LCF transport jam (paper not reaching 1st drawer transport sensor): Paper which has passed the 2nd drawer transport sensor does not reach the 1st drawer transport sensor during the feeding at the Tandem LCF.
 
 
 
 
 
E3E0
 
Tandem LCF transport jam (paper not reaching 2nd transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at
the Tandem LCF.
 
 
 
 
 
 
 
 
 
E3F0
 
 
Tandem LCF transport jam (paper not reaching 3rd drawer / Tandem LCF transport sensor): Paper which has passed the 3rd drawer / Tandem LCF feed sensor does not reach the 3rd drawer / Tandem LCF transport sensor during the feeding at the Tandem LCF.
Cover open jam
 
 
E410
 
 
Front cover open jam: The front cover has opened during printing.
 
 
E440
Right lower cover (feed cover) open jam: The feed cover has opened during printing.
 
 
E450
Option LCF side cover open jam: The side cover of the Option LCF has opened during printing.
 
 
E460
Right center cover (bypass feed unit cover) open jam: The bypass feed unit cover has opened during printing.
 
 
E470
Left lower cover (exit cover) open jam: The exit cover has opened during printing.
Paper transport jam (Exit/Reverse section or other sections)
 
 
 
E510
Transport jam during duplex printing (paper not reaching reverse sensor-2): Paper which has passed the reverse sensor-1 does not reach the reverse sensor-2 during duplex printing.
 
 
 
 
 
E511
 
 
Transport jam during duplex printing (paper not reaching horizontal transport sensor-1): Paper which has passed the reverse sensor-2 does not reach the horizontal transport sensor-1 during duplex printing.
 
 
 
 
 
E512
 
Transport jam during duplex printing (paper not reaching horizontal transport sensor-2): Paper which has passed the horizontal transport sensor-1 does not reach the horizontal transport sensor-2 during duplex printing.
 
 
 
 
 
E540
 
Transport jam during duplex printing (paper not reaching horizontal transport sensor-3): Paper which has passed the horizontal transport sensor-2 does not reach the horizontal transport sensor-3 during duplex printing.
 
 
 
E550
Paper remaining jam at paper transport path: Paper is remaining on the paper transport path when the printing has finished. (Jam caused by a multiple paper feeding)
 
 
E551
 
 
Paper remaining on the transport path (when a service call occurs)
 
 
E552
 
 
Paper remaining on the transport path (when the cover is closed)
 
 
 
 
 
 
 
 
E570
 
 
Transport jam during duplex printing (paper not reaching reverse
sensor-1): Paper which has passed the fuser unit transport sensor does not reach the reverse sensor-1 during duplex printing.
 
 
 
 
 
E580
 
 
Paper stopping at reverse section: The trailing edge of paper does not pass the reverse sensor-1 or reverse sensor-2 after its leading edge has reached the reverse sensor-1 or reverse sensor-2.
 
 
 
E590
 
 
Paper stopping at exit section: The trailing edge of paper does not pass the exit sensor after its leading edge has reached the exit sensor.
 
 
E5A0
Paper not reaching exit sensor: The leading edge of paper does not reach the exit sensor.
RADF jam
 
 
 
E712
 
 
Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor.
 
 
E714
Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.
 
 
 
 
 
E721
 
Jam not reaching the original reading start sensor: The original does not reach the original reading start sensor after it has passed the original registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).
 
 
 
 
 
E722
 
 
Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit sensor when it is transported from the scanning section to exit section.
 
 
 
E724
Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor.
 
 
 
E725
Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
E726 Transport/exit signal reception jam during ADF standby status
E727 Jam not reaching the original reading end sensor
E729 Original reading end sensor paper remaining jam
 
 
 
E731
Stop jam at the original exit sensor: The trailing edge of the original
does not pass the original exit sensor after its leading edge has reached this sensor
E744 Stop jam at the original exit/reverse sensor
E745 Jam not reaching the original exit/reverse sensor
 
 
 
E746 Original exit/reverse sensor paper remaining jam
E762 Original registration sensor paper remaining jam
E770 Original width detection sensor-1 paper remaining jam
E771 Original width detection sensor-2 paper remaining jam
E772 Original width detection sensor-3 paper remaining jam
E773 Original Intermediate transport sensor paper remaining jam
E774 Original reading start sensor paper remaining jam
E775 Original reading end sensot paper remaining jam
E777 Original exit sensor paper remaining jam
 
 
E860
Original jam access cover open: The Original jam access cover has opened during RADF operation.
E870 RADF open jam: RADF has opened during RADF operation.
 
 
 
 
 
E871
 
 
Cover open jam in the read ready status: Jam caused by opening of the Original jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment.
E890 ADF time out jam
Finisher jam
E9F0 Hole punch jam: Hole punching is not performed properly.
 
 
EA10
Paper transport delay jam: Paper which has passed the exit sensor does not reach the inlet sensor.
 
 
EA20
Paper transport stop jam: Paper which has reached the inlet sensor does not pass the inlet sensor.
 
 
EA30
Power-ON jam: Paper is remaining at the inlet sensor when the power is turned ON.
 
 
 
EA40
Door open jam: The upper cover or the front cover of the Finisher has opened, or the upper door or the front door of the Hole Punch Unit has opened during printing.
EA50 Stapling jam: Stapling is not performed properly
 
 
EA60
Early arrival jam: The inlet sensor detects paper earlier than the specified timing
EA80 Stapling jam: Stapling is not performed properly.
 
 
EA90
Door open jam: The delivery cover or the inlet cover has opened during printing.
 
 
 
EAA0
Power-ON jam: Paper is remaining at the No. 1 paper sensor, No. 2 paper sensor, No. 3 paper sensor, vertical path paper sensor or delivery sensor when the power is turned ON.
 
 
 
EAB0
Paper transport stop jam: Paper which has passed the inlet sensor does not reach or pass the No. 1 paper sensor, No. 2 paper sensor, No. 3 paper sensor or delivery sensor.
 
 
 
 
 
EAC0
Transport delay jam: Paper which has reached the inlet sensor does not pass the inlet sensor.
 
 
 
EAD0
Print end command time-out jam: The printing has not finished normally due to the communication error between the SYS board and LGC board at the end of the printing.
 
 
 
 
 
EAE0
 
 
Receiving period time-out jam: The printing cannot be finished normally due to the communication error between the equipment and the Finisher when the paper is transported from the equipment to the Finisher.
 
 
 
 
 
EB30
 
 
Ready period time-out jam: The equipment judges that the paper transport to the Finisher is disabled due to the communication error between the equipment and the Finisher at the start of the printing.
Paper transport jam
 
 
 
EB50
 
 
Paper remaining on the transport path: The multiple feeding of the preceding paper caused the misfeeding of the upcoming paper.
 
 
 
EB60
Paper remaining on the transport path: The multiple feeding of the preceding paper caused the misfeeding of the upcoming paper (= redetection after no jam is detected at [EB50]).
Finisher jam (Inserter section)
EC00 Inserter feeding delay jam
EC10 Inserter feeding stop jam
EC20 Inserter reverse path delay jam-1
EC30 Inserter reverse path stop jam-1
EC40 Inserter reverse path delay jam-2
EC50 Inserter reverse path stop jam-2
EC60 Inserter transport delay jam-1
EC70 Inserter transport stop jam-1
EC80 Inserter transport delay jam-2
EC90 Inserter transport stop jam-2
ECA0 Paper remaining in Inserter Unit at power-ON
ECB0 Incorrect setting of paper size for Inserter Unit
ECC0 Inserter Unit misfeeding
ECD0 Inserter Unit door open jam
Paper feeding system related service call
 
 
 
C130
1st drawer tray abnormality: The tray-up motor-1 does not run normally or the 1st drawer tray does not move normally. (Feeding of any other drawer than the 1st drawer is possible.)
 
 
 
 
 
 
C140
2nd drawer tray abnormality: The tray-up motor-1 does not run normally or the 2nd drawer tray does not move normally. (Feeding of any other drawer than the 2nd drawer is possible.)
 
 
 
C150
3rd drawer tray abnormality: The tray-up motor-2 does not run normally or the 3rd drawer tray does not move normally. (Feeding of any other drawer than the 3rd drawer is possible.)
 
 
 
C160
4th drawer tray abnormality: The tray-up motor-2 does not run normally or the 4th drawer tray does not move normally. (Feeding of any other drawer than the 4th drawer is possible.)
 
 
 
 
 
C180
 
Tandem LCF tray-up motor abnormality: The Tandem LCF tray-up motor does not run normally or the Tandem LCF tray does not move normally. (Feeding of any other drawer than the Tandem LCF is possible.)
 
 
 
 
 
C1A0
 
Tandem LCF end fence motor abnormality: The Tandem LCF end fence motor does not run normally or the Tandem LCF end fence does not move normally. (Feeding of any other drawer than the Tandem LCF is possible.)
 
 
 
 
 
C1C0
 
 
Option LCF tray-up motor abnormality: The Option LCF tray-up motor does not run normally or the Option LCF tray does not move normally. (Feeding of any other drawer than the Option LCF is possible.)
Scanning system related service call
 
 
C260
Peak detection error: Lighting of the exposure lamp (white reference) is not detected when the power is turned ON.
 
 
 
C270
Carriage home position sensor not turning OFF within a specified period of time: The carriages do not shift from their home position within a specified period of time.
 
 
 
C280
Carriage home position sensor not turning ON within a specified period of time: The carriages do not reach their home position within a specified period of time.
 
 
C290
Scanner fuse blowout: 24V power for the scanning system is not supplied at the scanner warming-up after power-ON
Process related service call
 
 
 
C360
Wire cleaner drive motor abnormality: The wire cleaner drive motor does not run normally or the charger wire cleaner does not move normally.
 
 
 
C370
 
 
Transfer belt cam motor abnormality: The transfer belt cam motor does not run normally when the power is turned ON or the copying is started.
Fuser unit related service call
 
 
 
 
 
 
 
 
C411
 
 
Thermistor/heater abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON.
 
 
 
 
 
C412
 
 
Thermistor/heater abnormality at power-ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON.
 
 
C443
Heater abnormality after abnormality judgment (not reaching to intermediate temperature)
 
 
C445
Heater abnormality after abnormality judgment (prerunning end temperature abnormality)
 
 
C446
Heater abnormality after abnormality judgment (prerunning end temperature abnormality)
 
 
C447
Heater abnormality after abnormality judgment (temperature abnormality at ready status)
C449 Heater abnormality after abnormality judgment (overheating)
 
 
C465
Pressure roller thermistor abnormality after entering ready status (pre- running end temperature abnormality)
 
 
C466
Pressure roller thermistor abnormality after entering ready status (pre- running end temperature abnormality)
 
 
C467
Pressure roller thermistor abnormality after entering ready status
(temperature abnormality at ready status)
 
 
C468
Pressure roller thermistor abnormality after entering ready status
(overheating)
 
 
C471
IH power voltage abnormality or IH initial abnormality (IH board initial abnormality)
C472 IH power voltage abnormality (power supply abnormality)
 
 
C473
 
 
IH power voltage abnormality (power voltage upper limit abnormality)
 
 
C474
 
 
IH power voltage abnormality (power voltage lower limit abnormality)
 
 
C475
IH power voltage abnormality (power supply abnormality when door is opened)
C480 IH abnormality
C481 IGBT abnormality
 
 
 
C490
IH control circuit abnormality or IH coil abnormality: The IH control circuit is under abnormal conditions, or the IH coil is broken or has a short-circuit.
C4A0 End of cleaning web
C4B0 Fuser unit counter abnormality
 
 
 
Optional communication related service call
 
 
C550
RADF interface error: Communication error has occurred between the
RADF and the scanner.
C560 Communication error between Engine-CPU and PFC
C570 Communication error between Engine-CPU and IPC board
C580 Communication error between IPC board and Finisher
C590 Communication error between Engine-CPU and Laser-CPU
C5A1 NVRAM data abnormality (LGC board)
RADF related service call
 
 
C730
RADF EEPROM error: Data abnormality occurs during the EEPROM
writing of the RADF is performed.
 
 
C880
RADF original feed motor abnormality: An error signal has been detected when the motor is rotating
 
 
C890
RADF read motor abnormality: An error signal has been detected when the motor is rotating.
 
 
C8A0
RADF original reverse motor abnormality: An error signal has been detected when the motor is rotating.
 
 
C8B0
RADF original exit motor abnormality: An error signal has been detected when the motor is rotating
 
 
 
C8C0
RADF original reading start sensor abnormality: The automatic adjustment for the original reading start sensor has been performed, but is ended unsuccessfully.
 
 
C8E0
RADF communication protocol abnormality: The system has to be stopped because the control abnormality occurred.
Circuit related service call
C940 Engine-CPU abnormality
 
 
C970
High-voltage transformer leakage abnormality: The high-voltage leakage of the main charger is detected.
Laser optical unit related service call
 
 
CA10
Polygonal motor abnormality: The polygonal motor does not run normally.
 
 
CA20
H-sync detection error: Laser beam cannot be detected at the SNS
board.
CA30 Secondary scanning coarse adjustment error
 
 
CA41
Window comparator abnormality (error during secondary scanning control)
 
 
CA42
 
 
Sensor signal busy error (error during secondary scanning control)
CA43 Comparator abnormality
CA50 Laser power adjustment error
 
 
 
 
 
CA90
Image data transmission error of SYS board: Communication error has occurred between the PLG board and the SYS board.
 
 
CAA0
Secondary scanning fine adjustment error: Secondary scanning control by the galvanometer mirror does not end normally
 
 
 
CAB0
 
 
Inter-page correction error of secondary scanning: Inter-page secondary scanning control by the galvanometer mirror does not end normally.
 
 
CAC0
Primary scanning dot adjustment error: Primary scanning control does not end normally.
 
 
CAF0
Inter-page correction error of primary scanning: Inter-page primary scanning control does not end normally.
Finisher related service call
 
 
CB10
Feed motor abnormality: The feed motor does not run normally or the stack feed roller does not move normally.
 
 
CB20
Delivery motor abnormality: The delivery motor does not run normally or the delivery roller does not move normally.
CB30 Tray lift motor abnormality
 
 
 
CB40
 
 
Alignment motor (rear) abnormality: The alignment motor (rear) does not run normally or the alignment plate does not move normally
 
 
CB50
Staple motor abnormality: The staple motor does not run normally or the stapler does not move normally.
 
 
CB60
Stapler shift motor abnormality: The stapler shift motor does not run normally or the Staple Unit does not move normally.
CB70 Stack amount detection sensor abnormality
 
 
 
 
 
 
CB80
 
 
Backup RAM data abnormality: 1. Abnormality of checksum value on the finisher controller PC board is detected when the power is turned ON. 2. Abnormality of checksum value on the punch controller PC board is detected when the power is turned ON.
 
 
 
CB90
Paper pushing plate motor abnormality: The paper pushing plate motor does not run normally or the paper pushing plate does not move normally.
 
 
CBA0
Stitch motor (front) abnormality: The stitch motor (front) does not run normally or the rotational cam does not move normally.
 
 
CBB0
Stitch motor (rear) abnormality: The stitch motor (rear) does not run normally or the rotational cam does not move normally.
 
 
CBC0
Alignment motor abnormality: The alignment motor does not run normally or the alignment plate does not move normally.
 
 
CBD0
Guide motor abnormality: The guide motor does not run normally or the guide does not move normally.
 
 
 

[Quay lại]



Các tin liên quan

Bảng tra mã lỗi Toshiba Tiếng Việt Full

Bảng tra mã lỗi Toshiba E352/452 Full

 
 
 
CBE0
 
 
Paper folding motor abnormality: The paper folding motor does not run normally or the paper folding roller does not move normally.
 
 
 
CBF0
Paper positioning plate motor abnormality: The paper positioning plate motor does not run normally or the paper positioning plate does not move normally.
 
 
 
 
 
CC00
 
 
Sensor connector abnormality: Disconnection of each connector of the guide home position sensor, paper pushing plate home position sensor and paper pushing plate leading position sensor is detected.
 
 
 
CC10
Microswitch abnormality: Any of the inlet door switch, delivery door switch and front cover closing detection switch is opened while all the covers are closed.
 
 
 
CC20
Communication error between Finisher and Saddle Stitch section: Communication error has occurred between the finisher controller PC board and the saddle stitcher controller PC board.
 
 
CC40
Swing motor abnormality: The swing motor does not run normally or the swing unit does not move normally.
 
 
 
CC50
 
 
Horizontal registration motor abnormality: The horizontal registration motor does not run normally or the puncher does not move normally.